TS1201 Pinch Tube Valve

The TS1201 Dispensing Pen uses a disposable moulded tube assembly. Designed to handle a wide variety of low to medium viscosity fluids – from adhesives and lubricants to sealants and masks. Gravity or pressure fed, the pen has a built-in shot and flow rate for repeatability. Includes pre-assembled applicator pen, two clear and two black spare pinch tube assemblies, an assortment of disposable dispensing tips and a 24" hose. Replacement pinch tube assemblies supplied in packs of 10.

The valve uses disposable pinch tubes either clear plastic or black (for UV cure adhesives) and is supplied with 2 of each. The tube features a male luer lock at the tip end (to accept any standard needle/ tapered tips) and a female luer lock connector the other end. This allows you to connect the valve to fluid lines and then to a pressure pot, cartridge reservoir or syringe feed. The valve is kept closed (pinched) until the lever is pressed which opens the tube to allow fluid flow. Once the lever is released, the spring loaded rod pushes against the tube to seal and stop fluid flow. Replacing the tubes are quick and simple. Tubes will operate many cycles before replacement is required.

		Ideal for cyanoacrylates, UV cure and anaerobics   Zero cleanup with replaceable pinch tubes   Low cost dispensing solution   Controlled deposits, lines or potting   Syringe feed, cartridge or pressure pot   Supplied with pinch tubes, fluid lines and tip samples

Specifications
Part ID:	TS1201
Size:	5" (127mm) L x 1.34" (34mm) Diameter
Weight:	36g (0.08lb)
Wetted Parts:	Polyethylene
Viscosity Range:	1 - 45,000 CPS
Flow Rate (water):	0.54 GPM @ 60 psi
Max Fluid Pressure:	60 psi ( 4 Bar)
Material Inlet:	Female Luer Lock
Material Outlet:	Male Luer Lock
Typical Materials:	Cyanoacrylates, adhesives, oils, lubricants, anaerobics, solvents, activators, UV cure
Lead Time:	*Usually Ships in 1-2 Business Days
Price:	£65.00 each
Order Online:

TS5623HU Diaphragm Valve Manual Control UHMW Head Diaphragm Valves are designed to dispense low to medium viscosity materials with accuracy over a wide range of shot and bead sizes. A short opening stroke provides fast, positive shut-off. An external stroke control adjustment makes it easy to fine tune shot sizes. Body available in FDA-compliant Ultra High Molecular Weight Polyethylene (UHMWPE) for most applications. A Teflon® version for chemical compatibility, and a Delrin® version for UV-curable are also available. A stainless steel version with optimized internal fluid route is especially dedicated to dispense UV-cure adhesives, resins and lacquers used in the manufacture of DVDs and CDs. A hand-held actuated valve is also available. The valves are easy to use and maintain with user replaceable spare parts. This UHMW valve is most suited to cyanoacrylates, solvents, water, inks, primers and activators. The valve design is hand operation with manual control. Fluid is a either by syringe, cartridge or fluid line feed (from pressure pot).
		Ideal for cyanoacrylates, primers, activators   Low maintenance compact design   High precision and accuracy   Controlled lines or filling   Adjustable stroke control for fine tuning   Syringe feed, cartridge or pressure pot   Supplied with connector, fluid lines and tip kit   Easy hand lever control without fatigue
Specifications Part ID: TS5623HU Size: 3.47" (88mm) L x 1.06" (27mm) Diameter Weight: 118g (0.26lb) Wetted Parts: UHMW, Teflon® Viscosity Range: 1 - 50,000 CPS Flow Rate (water): 7250ml/minute @ 100 psi Max Fluid Pressure: 70 psi ( 5 Bar) Material Inlet: 1/8 NPT Material Outlet: 1/8 NPT Mounting: 10-32 UNF On/Off Pressure: 50 psi (3.4 Bar) Minimum Typical Materials: Cyanoacrylates, adhesives, oils, lubricants, anaerobics, solvents, activators Lead Time: *Usually Ships in 1-2 Business Days Price: £495.00 each Order Online: